JR GAS & WATER INSTALLER ASSESSMENT
Our Water Filtration Installer Verdict
This is our trade-side view of the product: how it is built, how practical it is to install and service, the plumbing layout, its NSF/ANSI certification status and the manufacturer support behind it.
--/100
JR GAS & WATER LOCAL INSTALLATION
Water Filter Installation Areas
View all water filter service areas
PURETEC WHOLE-HOUSE RAINWATER + UV FILTRATION
Puretec HYBRID-G13 Installation Brisbane & Gold Coast
JR Gas & Water supplies and installs the Puretec HYBRID-G13 whole-house rainwater filtration and UV system across eligible Brisbane, Gold Coast and surrounding South East Queensland service areas.
The current Puretec HYBRID-G13-LF combines three stages of 20-inch filtration with ultraviolet treatment in a purpose-built weather-protected enclosure. It is designed primarily for homes using rainwater and can also accommodate mains water applications where appropriate.
Water passes through a 5-micron pleated sediment cartridge, a 5-micron carbon block cartridge and a finer 1-micron polyspun cartridge before reaching the UV reactor. This provides progressive filtration before ultraviolet treatment is applied to the clarified water.
Puretec HYBRID-G13 at a glance: HYBRID-G13-LF, triple 20-inch filtration, PL05MP2 5-micron sediment cartridge, CB05MP2 5-micron carbon block cartridge, PX01MP2 1-micron sediment cartridge, RL6 46W UV lamp, RQS6 quartz sleeve, 1" BSP / 25mm connections, 70 L/min UV flow at the manufacturer-identified 30mJ/cm² drinking-water dose, outdoor weather enclosure, lockable lid and 3-year Puretec warranty.
Puretec HYBRID-G13 Supply & Installation at a Glance
Triple Filtration
Three 20-inch filtration stages progressively treat sediment and provide carbon treatment before the water reaches the UV chamber.
Ultraviolet Treatment
The RL6 ultraviolet system provides a chemical-free treatment stage targeting microorganisms including E. coli, Giardia and Cryptosporidium cysts.
70 L/min @ 30mJ/cm²
Puretec identifies 30mJ/cm² as the industry-standard UV dose for drinking water, with the G13 rated at 70 L/min at that dose.
Outdoor Enclosure
A weather-protection cover, corrosion-resistant construction and lockable lid make the G13 suitable for appropriately installed outdoor applications.
What Is the Puretec HYBRID-G13?
The Puretec HYBRID-G13 is an integrated whole-house rainwater treatment system combining triple-stage filtration and ultraviolet treatment.
Unlike a basic sediment filter, the G13 treats water through multiple filtration stages before exposing it to ultraviolet light.
This allows the system to address sediment, unpleasant taste and odour, chlorine and other carbon-treatable contaminants while also providing an ultraviolet treatment stage for microbiological protection.
The system is installed on the incoming water supply so treated water can be distributed to connected taps, showers, laundries and other household outlets.
How Does the Puretec HYBRID-G13 Treat Rainwater?
Stage 1 – PL05MP2
The first stage uses a PL05MP2 5-micron pleated sediment cartridge to reduce dirt, rust, algae and suspended sediment.
Stage 2 – CB05MP2
The second stage uses a CB05MP2 5-micron carbon block cartridge to provide carbon treatment for contaminants including chlorine, unpleasant taste and odour.
Stage 3 – PX01MP2
The third stage uses a PX01MP2 1-micron polyspun sediment cartridge to provide finer particulate filtration before the UV treatment stage.
Final treatment – ultraviolet: After passing through the three filtration stages, water enters the UV chamber where the RL6 lamp provides ultraviolet treatment. The effectiveness of UV treatment depends on water clarity, correct flow, lamp condition, quartz-sleeve condition and proper system maintenance.
Why Choose the Puretec HYBRID-G13?
Filtration + UV in One System
The G13 combines mechanical filtration, carbon treatment, fine filtration and UV treatment in one integrated package.
Designed for Rainwater
Puretec specifically designs its Hybrid UV systems around common residential rainwater treatment applications.
Large 20-Inch Cartridges
The G13 uses three 20-inch cartridges, providing greater filtration capacity than the smaller 10-inch HYBRID-G12 format.
Outdoor Protection
The weather cover protects the filtration and UV components while providing a cleaner finished installation.
Lockable Lid
An anti-tamper and child-resistant lockable lid helps restrict access to the system's filtration and UV components.
UV Monitoring
The UV controller includes a lamp countdown timer plus audible and visible failure alarms to assist with ongoing system maintenance.
PRODUCT SUITABILITY
Is the Puretec HYBRID-G13 Right for Your Home?
A Strong Fit If...
Your home relies on rainwater and you want whole-house filtration combined with UV treatment rather than sediment filtration alone.
Especially Relevant If...
You want carbon treatment for taste, odour and chlorine alongside finer sediment filtration and microbiological treatment.
Assessment May Be Needed If...
Your tank water is highly turbid, heavily stained or otherwise has poor UV transmission. UV performance depends on sufficient water clarity.
Rainwater and Mains Water Applications
Puretec designs the HYBRID-G13 primarily for rainwater supply and also states that the system is suitable for mains and rainwater applications.
This can make the G13 relevant to properties where rainwater is the principal household supply as well as configurations where town water forms part of the overall plumbing arrangement.
The actual installation needs to account for how rainwater and mains supplies are controlled, whether a rainwater pump is already installed and how the home's water-source changeover arrangement operates.
Puretec HYBRID-G13 Specifications
| Brand | Puretec |
|---|---|
| Current Model | HYBRID-G13-LF |
| Product Type | Triple-stage whole-house filtration + ultraviolet treatment |
| Primary Application | Rainwater whole-house treatment |
| Other Application | Mains water where appropriate |
| Filter Format | Triple 20-inch filtration |
| Stage 1 Cartridge | PL05MP2 |
| Stage 1 | 5-micron pleated sediment filtration |
| Stage 2 Cartridge | CB05MP2 |
| Stage 2 | 5-micron carbon block filtration |
| Stage 3 Cartridge | PX01MP2 |
| Stage 3 | 1-micron polyspun sediment filtration |
| UV Lamp | RL6 |
| UV Lamp Power | 46W |
| Quartz Sleeve | RQS6 |
| UV Flow @ 40mJ/cm² | 54 L/min |
| UV Flow @ 30mJ/cm² | 70 L/min |
| UV Flow @ 16mJ/cm² | 130 L/min |
| Published Filtration Flow | 120 L/min |
| Connection | 1" BSP / 25mm |
| Supply Pressure | 300–875kPa* |
| Water Temperature | 0–52°C, protect from freezing |
| Outdoor Installation | Weather-protected enclosure provided |
| UV Monitoring | Lamp countdown timer + audible and visible failure alarm |
| Current Puretec Warranty | 3 years |
*Puretec specifies that where line pressure exceeds 500kPa, an approved pressure-limiting device must be installed in accordance with applicable Australian and New Zealand plumbing requirements.
Understanding the HYBRID-G13 Flow Ratings
The HYBRID-G13 has several published flow figures, and they should not be treated as interchangeable.
Puretec describes the G13 filtration platform as suitable for approximately 120 L/min, while the ultraviolet reactor has separate maximum flow rates based on the UV dose delivered.
| UV Dose | Maximum Published Flow | Meaning |
|---|---|---|
| 40mJ/cm² | 54 L/min | Higher UV dose with lower allowable flow |
| 30mJ/cm² | 70 L/min | Puretec identifies this as the industry-standard dose for drinking water |
| 16mJ/cm² | 130 L/min | Lower UV dose at higher flow |
For drinking-water applications, the relevant Puretec-published benchmark is therefore 70 L/min at 30mJ/cm², not simply the 120 L/min filtration rating.
Why UV Dose Matters
Ultraviolet treatment works by exposing microorganisms to UV light as water passes through the reactor.
The UV dose depends partly on how quickly water travels through the chamber. Higher flow provides less exposure time, which is why Puretec publishes different maximum flow rates for different UV doses.
This is particularly important when sizing the G13 for a larger home. The filtration housings may be capable of greater flow than the flow used for a particular UV-dose target.
UV Treatment for E. coli, Giardia and Cryptosporidium
Puretec specifically states that Hybrid UV technology is highly effective against microorganisms including E. coli, Giardia and Cryptosporidium cysts when the system is correctly selected, installed, operated and maintained.
UV treatment works without adding disinfecting chemicals to the water.
Unlike sediment or carbon filtration, UV treatment does not physically filter microorganisms out of the water. Instead, UV light provides the microbiological treatment as water passes through the reactor.
For this reason, correct filtration before the UV chamber is an important part of the HYBRID-G13 design.
Why Water Clarity Matters for UV
Puretec specifically warns that UV effectiveness depends on the clarity of the water.
Particles, turbidity and certain dissolved or suspended materials can reduce UV transmission and interfere with effective treatment.
The G13's three filtration stages are designed to prepare common rainwater for UV treatment, but unusually poor or heavily stained water may require additional assessment.
Puretec advises that a UVT test can be used where there is uncertainty about whether the incoming water has adequate ultraviolet transmission or requires additional treatment before the UV stage.
What Does the Puretec HYBRID-G13 Treat?
Sediment
Dirt and suspended particles
Rust and particulate material
Chlorine through carbon treatment
Unpleasant taste
Unpleasant odour
Selected carbon-treatable chemicals
E. coli through UV treatment
Giardia through UV treatment
Cryptosporidium cysts through UV treatment
The HYBRID-G13 should not be confused with reverse osmosis or water softening. It does not use an RO membrane and is not designed to remove dissolved salts or hardness in the way those treatment technologies do.
Outdoor Weather-Protected Design
One of the major differences between the HYBRID-G13 and an exposed filter-and-UV arrangement is its integrated outdoor enclosure.
Puretec specifically provides the Hybrid G Series with a weather-protection cover for outdoor installation.
The system also uses anti-corrosion construction, a high-strength aluminium mounting bracket and an anti-tamper, child-resistant lockable lid.
The hinged lid provides access to the UV lamp for routine maintenance without dismantling the complete enclosure.
UV Lamp Countdown Timer and Failure Alarm
The HYBRID-G13 is equipped with a lamp countdown timer and audible and visible failure alarm.
These monitoring functions are important because a UV lamp can still appear illuminated even when its useful UV output has declined below the required treatment level.
The UV lamp therefore needs to be replaced according to Puretec's servicing requirements rather than waiting for the lamp to visibly stop operating.
Puretec HYBRID-G13 vs Basic Whole-House Filtration
| Capability | HYBRID-G13 | Basic Sediment / Carbon System |
|---|---|---|
| Sediment Filtration | Yes – triple-stage treatment | Usually |
| Carbon Treatment | Yes | Model dependent |
| Fine 1-Micron Stage | Yes | Model dependent |
| UV Treatment | Yes | No unless separately added |
| Microbiological Treatment | UV treatment included | Not provided by ordinary sediment/carbon filtration |
| Outdoor Enclosure | Included | Model dependent |
| UV Alarm / Timer | Included | Not applicable without UV |
The main reason to choose the G13 over a basic whole-house filter is not simply additional filtration capacity. It is the addition of an integrated UV microbiological treatment stage.
Puretec HYBRID-G13 vs HYBRID-G12
| Specification | HYBRID-G13 | HYBRID-G12 |
|---|---|---|
| Filtration Stages | 3 | 3 |
| Cartridge Size | 20 inch | 10 inch |
| Stage 1 | PL05MP2 | PL05MP1 |
| Stage 2 | CB05MP2 | CB05MP1 |
| Stage 3 | PX01MP2 | PX01MP1 |
| Published Filtration Flow | 120 L/min | 60 L/min |
| UV Lamp | RL6 | RL6 |
| UV Flow @ 30mJ/cm² | 70 L/min | 70 L/min |
| Connection | 1" BSP | 1" BSP |
| Current Status | Current | Discontinued |
The G13's main advantage over the older G12 is its larger 20-inch filtration package and increased filtration capacity. Both use the same RL6 UV platform and therefore share the same published UV dose/flow figures.
HYBRID-G13 vs Puretec EM2 Filtration
Puretec's EM2 systems are excellent choices where the treatment requirement is primarily sediment filtration or sediment plus carbon treatment.
The HYBRID-G13 moves beyond that approach by combining three filtration stages with UV treatment.
Choose an EM2 When...
You primarily need whole-house sediment or sediment-and-carbon filtration and do not require integrated UV treatment.
Choose HYBRID-G13 When...
You want an integrated rainwater treatment system combining sediment, carbon, fine filtration and ultraviolet treatment.
Water Quality Still Matters
Neither product should be selected from model name alone. Incoming water quality and the intended use determine the required treatment process.
HYBRID-G13 Replacement Cartridges and UV Components
| Stage 1 Replacement | PL05MP2 |
|---|---|
| Stage 2 Replacement | CB05MP2 |
| Stage 3 Replacement | PX01MP2 |
| Replacement UV Lamp | RL6 |
| Replacement Quartz Sleeve | RQS6 |
Puretec specifies the use of genuine replacement cartridges and components for the HYBRID-G13.
Cartridge life depends on incoming water quality, sediment loading and household usage. The UV lamp and quartz sleeve also require routine maintenance because correct UV performance depends on lamp output and the ability of UV light to pass through the quartz sleeve into the water.
INSTALLATION REQUIREMENTS
What Is Required to Install the Puretec HYBRID-G13?
Suitable incoming rainwater or approved water source
Suitable outdoor installation position
Correct 1" / 25mm plumbing arrangement
Appropriate water pressure
Approved pressure limiting where required
Suitable isolation and bypass arrangement
Adequate servicing clearance
Suitable electrical supply for UV operation
Protection from freezing
Adequate incoming water clarity for UV treatment
Correct flow direction
Leak, flow and operational checks during commissioning
The HYBRID-G13 Requires Power
Unlike the filtration-only Puretec EM2 systems, the HYBRID-G13 includes an ultraviolet treatment system and therefore requires electrical power for UV operation.
The electrical supply and installation position need to suit the manufacturer's requirements and applicable electrical conditions.
If electrical work or a new suitable power point is required, this needs to form part of the overall installation scope.
The UV system should not be treated as operational when its lamp and controller are not correctly powered.
Pressure Requirements
Puretec's HYBRID-G Series technical data specifies a supply-pressure range of approximately 300–875kPa.
Puretec also states that where line pressure exceeds 500kPa, an approved pressure-limiting device must be installed to comply with applicable Australian and New Zealand plumbing requirements.
The site's actual pressure and pump arrangement should therefore be checked before commissioning the system.
What's Included With Puretec HYBRID-G13 Installation?
Genuine HYBRID-G13
Supply of the current HYBRID-G13-LF with PL05MP2, CB05MP2 and PX01MP2 cartridges, RL6 UV lamp, RQS6 quartz sleeve and integrated outdoor enclosure.
Plumbing Installation
Mounting and connection to suitable existing plumbing, together with applicable flushing, leak checks and commissioning.
System Setup
Operational checks of the filtration and UV system plus guidance on ongoing cartridge, UV lamp and quartz-sleeve servicing.
Additional bypass plumbing, isolation valves, pressure limiting, pipework alterations, rainwater-pump work, mains/rainwater changeover alterations, structural work or electrical work may require additional installation scope.
How Much Does Puretec HYBRID-G13 Installation Cost?
Current supplied-and-installed pricing is shown through JR's live product and installation options where available.
The final Puretec HYBRID-G13 installation cost depends on the existing rainwater plumbing, pipe size, pump arrangement, pressure, mounting position, electrical supply, bypass requirements and whether mains/rainwater changeover equipment is involved.
A straightforward installation beside suitable existing plumbing and power is generally simpler than an installation requiring extensive pipework, pump relocation, pressure control or electrical upgrades.
BRISBANE INSTALLATION
Puretec HYBRID-G13 Installation Brisbane
JR Gas & Water supplies and installs the Puretec HYBRID-G13 in Brisbane for suitable whole-house rainwater treatment applications.
The system is particularly relevant to tank-water properties wanting a more complete treatment process than sediment filtration alone, combining three-stage filtration with ultraviolet treatment in a weather-protected enclosure.
JR considers the rainwater source, pump performance, peak household flow, incoming water clarity, pipe size, water pressure, electrical supply and servicing access before confirming the installation arrangement.
GOLD COAST INSTALLATION
Puretec HYBRID-G13 Installation Gold Coast
JR Gas & Water also supplies and installs the Puretec HYBRID-G13 on the Gold Coast across eligible service areas.
For homes using tank water as a major or primary water supply, the G13 provides a purpose-built pathway combining sediment filtration, carbon treatment, fine filtration and UV treatment before water is distributed through the property.
JR assesses the existing tank, pump, plumbing, pressure, electrical access and water-treatment requirements before commissioning the system.
Can the HYBRID-G13 Replace My Existing Rainwater Filtration System?
Replacing an Older Hybrid
Existing pipework and power may simplify the installation, but connection layout, pressure and service clearance still need to be checked.
Upgrading From an EM2
The G13 adds a third filtration stage and UV treatment, so the installation also requires suitable electrical supply and additional space.
Replacing Separate Filters + UV
The G13 can consolidate filtration and UV equipment into a purpose-built weather-protected Puretec enclosure where the hydraulic requirements suit.
New Rainwater System
A new installation should be designed around tank capacity, pump performance, peak household demand, plumbing and water quality.
Mains + Rainwater Setup
The G13 can form part of a system using both water sources, but the existing changeover arrangement needs to be considered separately.
Poor Water Clarity
Additional testing or treatment may be required where incoming water has poor UV transmission or unusually high contamination loading.
COMMON QUESTIONS
Puretec HYBRID-G13 Installation FAQs
What is the current Puretec HYBRID-G13 model?
Puretec currently identifies the system as HYBRID-G13-LF.
Is the HYBRID-G13 designed for rainwater?
Yes. Puretec specifically designs the Hybrid G Series for whole-house rainwater treatment.
Can the HYBRID-G13 be used with mains water?
Yes. Puretec states that the G13 is designed for both mains and rainwater supply applications where the installation arrangement is appropriate.
How many filtration stages does the HYBRID-G13 have?
It has three 20-inch filtration stages followed by ultraviolet treatment.
What cartridges does the HYBRID-G13 use?
The current system uses PL05MP2, CB05MP2 and PX01MP2.
What does Stage 1 do?
Stage 1 uses a PL05MP2 5-micron pleated sediment cartridge for reducing sediment and suspended particulate material.
What does Stage 2 do?
Stage 2 uses a CB05MP2 5-micron carbon block cartridge, providing carbon treatment for contaminants including chlorine, unpleasant taste and odour.
What does Stage 3 do?
Stage 3 uses a PX01MP2 1-micron polyspun cartridge for finer sediment filtration before the UV chamber.
What UV lamp does the HYBRID-G13 use?
The G13 uses the Puretec RL6 46W UV lamp.
What quartz sleeve does it use?
The replacement quartz sleeve is the Puretec RQS6.
What is the HYBRID-G13 flow rate?
Puretec describes the filtration package as approximately 120 L/min. UV flow depends on the required dose: 54 L/min at 40mJ/cm², 70 L/min at 30mJ/cm² and 130 L/min at 16mJ/cm².
Which UV flow rate applies to drinking water?
Puretec identifies 30mJ/cm² as the industry-standard dose for drinking water. The G13's published maximum flow at that dose is 70 L/min.
Why isn't the 120 L/min figure the drinking-water UV flow rate?
The 120 L/min figure relates to the filtration platform. The UV reactor has separate flow limits based on the UV dose being delivered.
Does the HYBRID-G13 treat E. coli?
Puretec states that its Hybrid UV technology is highly effective against E. coli when the system is correctly installed, operated and maintained under suitable water conditions.
Does it treat Giardia and Cryptosporidium?
Puretec specifically includes Giardia and Cryptosporidium cysts among the microorganisms addressed by its Hybrid UV technology.
Does the HYBRID-G13 reduce chlorine?
Yes. Puretec lists chlorine and other chemicals among the contaminants reduced through the G13's filtration package, which includes a carbon block stage.
Does it improve taste and odour?
Yes. Puretec specifically lists reduction of bad taste and odour among the system's filtration benefits.
Does the HYBRID-G13 require electricity?
Yes. Electrical power is required to operate the ultraviolet treatment system and controller.
Can the HYBRID-G13 be installed outdoors?
Yes. The Hybrid G Series incorporates a weather-protection enclosure specifically intended for suitable outdoor installations.
Does it have a lockable cover?
Yes. Puretec provides an anti-tamper and child-resistant lockable lid.
Does the UV system have an alarm?
Yes. Puretec specifies a lamp countdown timer plus audible and visible failure alarms.
Why does water clarity matter?
UV treatment depends on ultraviolet light passing effectively through the water. Poor clarity can reduce UV transmission and may require additional filtration or assessment.
What happens if my rainwater is heavily stained or cloudy?
The water should be assessed before relying on the standard G13 configuration. Puretec can arrange UV-transmission testing where water clarity is uncertain.
What pipe connection does the HYBRID-G13 use?
The system uses 1-inch BSP / 25mm connections.
What pressure can the HYBRID-G13 operate at?
Puretec's technical data specifies approximately 300–875kPa. Where pressure exceeds 500kPa, Puretec specifies an approved pressure-limiting device.
What is the water-temperature range?
Puretec specifies approximately 0°C to 52°C and requires protection from freezing.
Does the HYBRID-G13 include a rainwater pump?
The HYBRID-G13 is the filtration and UV package. Puretec's HybridPlus range contains models incorporating or accommodating additional pump and water-management equipment. Existing or required pump arrangements should be assessed separately.
How often does the HYBRID-G13 need servicing?
Servicing includes cartridge replacement plus UV lamp and quartz-sleeve maintenance. Actual cartridge life depends on water quality and usage, while UV components should be maintained in accordance with Puretec's current service instructions.
What warranty does the HYBRID-G13 have?
Puretec currently publishes a 3-year warranty for the HYBRID-G13.
How much does HYBRID-G13 installation cost?
Installation cost depends on existing plumbing, rainwater-pump arrangement, electrical supply, pressure control, mounting location, bypass requirements and any additional work required at the property.
Can JR install the Puretec HYBRID-G13 in Brisbane or the Gold Coast?
Yes. JR supplies and installs suitable Puretec rainwater filtration and UV systems across eligible Brisbane, Gold Coast and surrounding South East Queensland service areas.
Puretec HYBRID-G13 Warranty
3-Year Puretec Warranty
Puretec currently publishes a 3-year warranty for the HYBRID-G13 system.
Consumable Components
Filter cartridges and other routine service items are consumable components and should be maintained according to Puretec's requirements.
Correct Maintenance Matters
UV treatment performance depends on correct lamp, quartz-sleeve and filtration maintenance throughout the system's service life.
Puretec product warranty and JR installation workmanship warranty are separate. Current warranty conditions supplied with the actual system should be retained by the owner.
Claims Strengthened or Cleaned Up From the Existing HYBRID-G13 Copy
Added exact HYBRID-G13-LF model identification
Confirmed triple 20-inch filtration configuration
Added exact PL05MP2 Stage 1 cartridge
Added exact CB05MP2 Stage 2 carbon cartridge
Added exact PX01MP2 Stage 3 cartridge
Added exact RL6 46W UV lamp
Added exact RQS6 quartz sleeve
Separated filtration flow from UV-dose flow ratings
Confirmed 54 L/min at 40mJ/cm²
Confirmed 70 L/min at 30mJ/cm²
Confirmed 130 L/min at 16mJ/cm²
Clarified Puretec's 30mJ/cm² drinking-water benchmark
Confirmed 1" BSP / 25mm connections
Confirmed 300–875kPa published pressure range
Added pressure-limiting requirement above 500kPa
Confirmed 0–52°C water-temperature range
Confirmed outdoor weather-protection enclosure
Confirmed anti-tamper lockable lid
Confirmed UV lamp countdown timer and failure alarms
Clarified importance of UV transmission and water clarity
Removed generic claims that cheaper systems are inherently unreliable
Clarified that UV effectiveness depends on correct flow and maintenance
Confirmed current 3-year Puretec warranty
Why Choose JR Gas & Water for Rainwater Filtration & UV?
JR Gas & Water supplies and installs whole-house rainwater filtration systems across Brisbane, the Gold Coast and eligible surrounding South East Queensland service areas.
Correct UV system selection involves more than choosing a filter by its advertised maximum flow. Water source, tank condition, incoming water clarity, UV transmission, rainwater-pump performance, peak household demand, pipe size, pressure, electrical supply and future servicing access all influence the finished treatment system.
JR assesses the installation requirements before confirming whether the HYBRID-G13, a filtration-only EM2 system or another rainwater treatment configuration is the more appropriate option.
COMPARE YOUR OPTIONS
Compare Puretec Rainwater Filtration Systems
Puretec Rainwater Filtration Systems
Compare JR's current Puretec rainwater filtration, whole-house filtration and UV treatment options for Brisbane, Gold Coast and South East Queensland properties.
READY TO INSTALL
Install the Puretec HYBRID-G13 With JR Gas & Water
The Puretec HYBRID-G13-LF combines three stages of whole-house filtration with ultraviolet treatment inside a weather-protected outdoor enclosure.
Its strongest fit is homes relying on rainwater that want a more complete treatment pathway than sediment or carbon filtration alone, particularly where microbiological treatment forms part of the water-quality requirement.
JR Gas & Water supplies and installs suitable Puretec HYBRID-G13 systems across eligible Brisbane and Gold Coast service areas. Choose the applicable live installation option above, or use JR's quote pathway where the project involves rainwater-pump changes, mains/rainwater changeover, pressure control, electrical work, extensive pipework alterations or non-standard water-quality conditions.